Buying the SCM L'invincibile TI 5 Tilting Spindle Moulder machine means you get a customised solution because it is the result of years of experience, technical research, Italian creativity.

Advantages

Electrospindle
Machining centre technology service for the woodworker. Absolute machining precision and absence of vibration due to the perfectly balanced structure of the electrospindle. The electrospindle’s direct drive eliminates maintenance procedures common with conventional belt driven systems.

"FAST" sectional worktable:
The best support for the workpiece. Provides support for the work piece being machined also close to the tool, allowing the adjustment with mounted tools.

"FLEX" fence
Immediately in the correct position. A single simple movement to retract and re-position in an instant and accurately position the fence on the worktable with such precision that no other control is necessary (SCM patent).

"Easy touch"
The operating advantage for easy assistance. Integrated and fast control of all dedicated functions. These features translate into immediate improvements in productivity and guarantees the capability of the full potential of the machine.

Preconfigured Versions

• 55.50.79: "EASY TOP" version complete with:
  • electrospindle with max. available motor power from 3400 rpm
  • 7.5kW 10HP electrospindle motor power
  • HSK 63B rapid tool changer
  • air blower system to maintain cleaned coupling contact surfaces
  • 1 tool-holder shaft with HSK 63B taper
  • inverter for electronic programming of the shaft rotating speed from 900 to 12000
    rpm
• H-E version with:
• “Fast” section table with automatic movement
• feeder support with automatic adjustments
• 55.51.16: "EASY TOP" Plus version complete with:
  • electrospindle with max. available motor power
    from 3400 rpm
  • 7.5kW 10HP electrospindle motor power
  • HSK 63E rapid tool changer
  • air blower system to maintain cleaned coupling contact
    surfaces
  • 1 tool-holder shaft with HSK 63E taper
  • inverter for electronic programming of the shaft rotating speed from 900 to 12000 rpm
• H-E Plus version with:
• “Fast” section table with automatic movement
• feeder support with automatic adjustments

Standard Equipment

• MK5 interchangeable spindle. The MK5 interchangeable spindle includes the presetting for the “T-SET”rapid tool locking.
• N.B.: The MK5 interchangeable spindle allows to purchase the “T-SET” device as accessory to retrofit the machine.
• M-E version complete with:
• electrospindle with max. available motor power from 3400 rpm
• 7.5kW 10hp electrospindle motor power
• MK5 interchangeable spindle
• inverter for electronic programming of the shaft rotating speed from 900 to 12000 rpm
• N.B.: Pneumatic working pressure 6 bar
• "Flex" spindle moulder fence with automatic adjustment managed by electronic control programming of the entire fence with reference to the tool diameter and the infeed fence with
  reference to the requested removal. FLEX system for the exclusion of the fence from worktable
• Aluminium profiling fence with connecting bars between the two tables
• Upper mobile control panel
• "Easy Touch 7" electronic control complete with:
• 7” LCD colour display with touch-screen system on upper mobile control panel
• Control of the 6-8 working axes with manual, semi-automatic and automatic mode
• Storage capacity up to 1000 programs with relevant picture, name and identification number
• Storage capacity up to 500 different tools with relevant picture, name and identification number
• Operator's help function on electronic control complete with:
  
  • management of the coordinates for the 3 different tool points being capable to define an origin (new zero point for the machine) on a selected tool point
  • tool peripheral speed management
  • operator's help for the more recurrent machining
• "Fast" section table with manual adjustment replacing the table rings, to optimize the working support under the cutting tool
• Electric presetting for feeder support
• Reverse spindle rotation
• Automatic star-delta start

Safety Equipment

• Spindle protection for operations (max. tool diameter 160 mm)
• Electronic brake ensuring stop, even in case of voltage drop
• Safety sensors for changing tool operation, spindle rotating stop control, tool taper locking/unlocking control
  
  • N.B.: Standard for H-E and H-E Plus versions
• Electro-pneumatic spindle locking
  
  • N.B.: It is foreseen for M-E version
• Safety microswitch on motor acess door 
• Emergency pushbuttons 
• Padlockable main switch 
• Overload switch protection
• Auxiliary low voltage (110 volts)
• Certificate of conformity with "CE standards"

Technical Specification

• Spindle tilting: +45°, 50° to -45°, 50°
• Rapid tool change: HSK B 63 H-E version
• Working length of spindle diameter 30-35 (40-50): 140 (160) [140 (140) H-E version]
• Spindle base projection from table: 250 mm
• Spindle rotating speed: 3000 / 4500 / 6000 / 7000 / 10000 rpm
• Max tool diameter retractable under worktable: 300 x 80 mm
• FLEX spindle moulder stroke (positioning with respect to the spindle axis): 250 mm (from -125 mm to +125 mm)
• External diameter of exhaust outlet on spindle moulder hood: 120 mm
• External diameter of exhaust outlet on base (for forced electrospindle aircooling 7.5kW): 2 x 100 mm (1 x 100 mm)
• Air flow speed of exhaust hood: 20
• Exhaust system air consumption: 2500 m³/h (7.5kW) [2000 m³/h (11kW)]

Optional Extras

• 13.02.09: Spare spindle (for MK5 interchangeable spindle)
• 57.02.10: MK5 right tool taper, complete with ring and collet
  complete with ER 32 type clamp, 1/2” diameter
• 57.02.11: MK5 left tool taper, complete with ring and collet complete with ER 32 type clamp, 1/2” diameter
• 57.02.88: "T-SET" rapid tool locking
• A simple compressed air gun allows the tools locking and unlocking
  
  • N.B.: Not available together with H-E and H-E Plus versions
  • “T-SET” is compatible with only one tool diameter. In case you select additional spare spindles for MK interchangeable spindle with different diameter with respect to the diameter selected during machine composition, it is necessary to order a number of “T-SET” system equal to the different diameters of the selected spindles
• 57.02.13: * H-E version complete with:
  
  • HSK 63B rapid tool changer
  • air blower system to maintain cleaned coupling contact surfaces
  • 1 tool-holder shaft with HSK 63B taper
    
    • N.B.: -pneumatic working pressure 6 bar
• 57.02.14: 1 additional tool-holder shaft with HSK 63B taper
• 57.02.32: 4 tool-holder shafts with HSK 63B taper. Complete with tool rack with 5 tool-holder shaft housings
• 53.02.12: HSK 63B right tool taper, complete with lock nut, without collet
• 53.02.13: HSK 63B left tool taper, complete with lock nut, without collet
• 57.04.04: * H-E Plus version complete with:
  
  • HSK 63E rapid tool changer
  • air blower system to maintain cleaned coupling contact surfaces
  • 1 tool-holder shaft with HSK 63E taper
  • N.B.: pneumatic working pressure 6 bar
• 57.04.05: 1 additional tool-holder shaft with HSK 63E taper
• 57.04.06: 4 tool-holder shafts with HSK 63E taper. Complete with tool rack with 5 tool-holder shaft housings
• 57.04.09: HSK 63E right tool taper, complete with ring and collet
• 57.04.10: HSK 63E left tool taper, complete with ring and collet
• 21.18.27: Mobile trolley complete with two tool racks
  
  • N.B.: Available only for H-E and H-E Plus versions
• 57.02.89: SAV€NERGY intelligent system for the management of the machine's energy consumption in order to eliminate any wastage. It includes the following functions:
  
  • exhaust system optimisation
  • automatic stand-by
  • intelligent control of the electrospindle cooling
  • compressed air optimisation with automatic sectioning of the pneumatic air supply
  • N.B.: It is available only coupled with the M-E, H-E or H-E Plus versions
• 57.04.11: Presetting for AIGNER fences with connecting bars between the two tables
• 57.03.19: "Easy Touch 12" control complete with:
  
  • 12” LCD colour display with touch-screen system on upper mobile control panel
  • Control of the 6-8 working axes with manual, semi-automatic and automatic mode
  • Storage capacity up to 1000 programs with relevant picture, name and identification number
  • Storage capacity up to 500 different tools with relevant picture, name and identification number
  • N.B.: It is available only coupled with “EASY TOP” and “EASY TOP plus” versions
• 57.01.59: * "FAST" section table with automatic adjustment managed from "Easy" control. Additional module for the "Easy" electronic programmer for the "Fast" section table programming.
  
  • N.B.: The option is available only together with Flex" spindle moulder fence with automatic adjustment
• 11.02.93: "LL" version with 2 cast-iron profiling extensions
  with:
  
  • total length of table 2500 mm complete with front support bar for large workpieces
  • emergency pushbutton.
• 11.02.05: Carriage on fixed table for small tenoning operations
  complete with + / - 60° swivelling fence with stops, telescopic extension and eccentric clamp. 250 mm max. tool diameter, with standard profiling fence.
• 57.01.05: PRO-10 "TL" version for tenoning-profiling
  with manual feed tenoning carriage with sliding on THK guides through recirculating ball bearing pads. It can be easily excluded from work table
  • +45°/-45° tiltable telescopic fence with reference to the feed direction
  • telescopic tilting fence with 4 reference stops for programming of workpiece length,
  • worktable with side extensions (2500 mm total length), complete with adjustable front support bar for large workpieces,
  • eccentric clamp
  • 1 anti-splinter device on fence with reference stop,
  • tenoning hood with exhaust hood:
    
    • with rapid tool change, max tool diam.300 mm,
    • with 30-35 mm spindle, max. tool diameter 300 mm
    • with 40-45 mm spindle, max. tool diameter 350 mm
  • emergency pushbutton,
  • operator arm protection,
  • microswitches for control and limit of 3000/4500 rpm during tenoning operations (only for CE configuration).
  • N.B.: available only together with spindle moulder fence with mechanical adjustment or as alternative the "Flex" spindle moulder fence
  • It is compulsory to select the inverter or M-E, H-E or H-E Plus versions for TF 5 model
• 57.02.57: * Manual vertical and horizontal feeder support
  Vertical adjustment with reference to the workpiece thickness to be processed, with mechanical digital readout of the position and horizontal adjustment with reference to the tool. This device, utilizing the column support of the upper mobile control panel allows the exclusion of the feeder from the working table
  
  • N.B.: Upper mobile control panel is compulsory
• 57.02.59: * Feeder support with automatic adjustment managed from electronic control. Vertical adjustment with reference to the workpiece thickness to be processed, with electronic digital readout of the position and horizontal adjustment with reference to the tool diameter. Automatic pneumatic locking system. This device, utilizing the column support of the upper mobile control panel allows the exclusion of the feeder from the working table
  
  • N.B.: Pneumatic working pressure 6 bar. The option is available only together with Flex" spindle moulder fence with automatic adjustment.
• 57.02.30: Glazing bead unit with rapid exclusion from the table. Technical features:
  
  • motor power 2,6 kW 3,5hp [S6 -40%]
  • tool diameter 200 mm max., 180 mm min., 30 mm maximum tool thickness
  • tool holder, 25 mm diameter
  • min. distance of the tool spindle axis from the working table 115 mm
  • exhaust hood, 80 mm diameter complete with:
    
    • – Glazing bead support complete with anti/kickback finger
    • – spindle fence with outfeed steel table, with adjustable insert, for the support during glazing
      bead operation, complete with stops
    • – counter opposed fence, applicable on the table
    • N.B.: The option is available only together with:
      
      • "LL" version with side table extensions or as alternative to the "TL" version for tenoning and profiling
      • "Flex" spindle moulder fence with automatic adjustment
      • For a better operating safety, it is advisable to utilize the feeder
• 57.04.13: 11kW 15hp electrospindle motor power

Note: Options marked with * are not available for preconfigured machines

Advanced Material Processing

• 53.03.20: Machine configuration for the machining of advanced materials. This configuration makes the machine suitable also for the machining of cork, stiff rubber or plastic and plastic-coated plywood. Metals and cement-wood base composite are excluded.
  
  • N.B.: For material which are not included in the list
    Due to the high variety of the extra-wood market, prior to engaging in the offer of a technical solution it is compulsory to send to SCM some material samples to carry out a proper check