The SCM Nova SI 400 Sliding Table Saw is a programmed or manual circular saw with 400mm blade. Guaranteed quality at your finger tips.

Advantages

Saw unit: a perfect cut.
Maximum torsional rigidity and the total absence of vibration through the closed loop structure of the saw unit which ensures perfect alignment of the blades during tilted and difficult cuts.

Sliding carriage: smooth sliding and a solid work surface.
The wide section of the carriage, with closed reticular geometry provides extreme rigidity and minimum deflection. A smooth operating motion is guaranteed over time by the system of sliding bearings running on hardened steel

Manual movements: always user friendly and precise.
Ease of use in every day operation due to the dedicated gear box, fully protected from dust (SCM patented solution), that provides a smooth and direct transmission. Every minimum handwheel movement corresponds to a precise blade adjustment.

Manual adjustment of the scoring unit: simple and effective.
Vertical and horizontal adjustments are carried out by user-friendly mechanical levers that operate directly making precise and smooth movements. The useful mechanical stops allows immediately finding of the set position. The positioning of the controls allows their use without moving from the front of the machine.

Standard Equipment

• 10 years guarantee for the carriage sliding system
• Anodized aluminium alloy carriage sliding on hardened steel guides, which are fixed on the carriage by means of mechanical
  bending system
• Sliding carriage length 3200mm
• Lifting and tilting of saw unit by means of handwheels on the machine front side and mechanical readout of saw unit tilt
• Squaring frame for the fast fence positioning of angular cuttings
• 2 reversible stops on the squaring fence
• Outfeed table extensions
• Dedicated saw parallel fencecomplete with:
  
  • "high rigidity" cast iron fence support
  • micrometric adjustment and cam-locking system
  • rectified steel round sliding bar, 45 mm diameter
• Ripping capacity on parallel fence 1270 mm
• Direct start main motor with pushbuttons
• Independent powered scoring unit with external setting up and stops for a quick re-positioning of the blade

Safety Equipment

• Emergency pushbuttons located on parallel fence side (CE version)
• Overload protection
• Overhead saw guard (CE version) with incorporated dust extraction and 80mm outlet diameter
• Blade protection on riving knife (CE version) with exhaust outlet 60mm
• Automatic brake on main sawblade (CE version)
• Padlockable main switch
• Auxiliary low voltage circuit (110 voltage)
• Certificate of conformity with "C.E. Standards" (CE version)
• 3 phase motor 7kW (9.5hp) 50Hz

Technical Specification

• Max cutting height at 90°: 140 mm
• Max cutting height at 45°: 97 mm
• Blade tilt: 45°
• Blades lifting and tilt: manual
• Main blade rotating speed: 3700 rpm
• Scoring unit rotating speed: 8500 rpm
• Saw unit motor power: 7 kW (9.5 hp) 50 Hz
• Scoring unit motor power: 1.3 kW (1.7 hp) 50 Hz
• Squaring capacity: 3200 x 3200 mm / 3200 x 3800 mm
• Cutting width on parallel fence: 1270 mm
• Exhaust outlet diameter:
  
  • at the base: 120 mm
  • on overhead protection: 80 mm
  • on riving knife: 60 mm

Optional Extras

• 57.03.20: Sliding carriage length 3800mm
  
  • Squaring capacity with scorer 3800 mm
• 57.03.21: Motor start/stop pushbuttons on the sliding carriage for saw and scoring blade
• 57.02.33: Squaring fence with no. 2 LCD readouts for stops position. Each stop with micrometric adjustment is equipped with electronic digital readout with detecting system on magnetic band and readout on LCD display
  • N.B.: The minimum height to position the stop near the blade is 350 mm. It is possible to fill up this limit purchasing a "third squaring stop with LCD display for the position readout".
• 57.03.39: Third squaring stop with LCD display for the position readout. With micrometric adjustment is equipped with electronic digital readout with detecting system on magnetic band and readout on LCD display.
  
  • N.B.: Only for squaring fence with 2 LCD readouts for stops position
• 57.01.24: Overhead saw guard with incorporated dust extraction 80 mm outlet diameter.
• 57.01.22: Angular cutting device with flip-over stops equipped with:
  
  • telescopic fence with two flip-over stops
  • pre-set for angle rapid selection
• 57.01.23: Device for angular cutting with self-adjustment of the stop position in respect of the blade, irrespective of the angles used, complete with aluminium fence with stop
• 57.03.22: Squaring frame with CompeX device
  for angular cutting with automatic self-adjustment of the stop position. This exclusive system allows the functioning even when the optional fence for complementary cuts is applied
  57.03.10: Fence for complementary cuttings to be applied to the squaring fence supplied as standard feature
• 57.01.62: Device for parallel cutting for rapid fixing on the carriage, complete with millimetric rule
• 57.03.43: Digital readout for parallel fence positions complete with digital display and magnetic band
• 57.02.25: Ripping capacity on parallel fence 1000 mm
• 57.01.26: Ripping capacity on parallel fence 1500 mm
• 53.03.40: Expandable scoring blade
  
  • Min. / max. thickness: 2.8 / 3.6 mm
  • Blade diameter: 120 mm
  • Bore diameter: 20 mm
  • Number of teeth: 24
• 57.03.36: "DADO" machining. Mechanical presetting to use a tool (not included) in place of the main blade.
  
  • – 203mm/8” max. diameter
  • – 30mm internal diameter
  • – 20mm maximum thickness
  • – 40mm max working depth
• 57.01.07: Eccentric clamp
• 57.01.33: 9kW (12hp) 50Hz

Advanced Material Processing

• 53.03.30: Machine configuration for the machining of advanced materials. This configuration makes the machine suitable also for the machining of cork, stiff rubber or plastic and plastic-coated plywood. Metals and cement-wood base composite are excluded.
• 53.03.16: Device for the blade micro-lubrication to machine plastic materials and light alloys of aluminium and brass with quantity adjusting system of the sprayed liquid lubrication
  
  • N.B.: The device is compulsory for the machining of light alloys of aluminum and brass, particularly useful with certain plastic materials